\relax 
\providecommand\hyper@newdestlabel[2]{}
\providecommand\HyperFirstAtBeginDocument{\AtBeginDocument}
\HyperFirstAtBeginDocument{\ifx\hyper@anchor\@undefined
\global\let\oldcontentsline\contentsline
\gdef\contentsline#1#2#3#4{\oldcontentsline{#1}{#2}{#3}}
\global\let\oldnewlabel\newlabel
\gdef\newlabel#1#2{\newlabelxx{#1}#2}
\gdef\newlabelxx#1#2#3#4#5#6{\oldnewlabel{#1}{{#2}{#3}}}
\AtEndDocument{\ifx\hyper@anchor\@undefined
\let\contentsline\oldcontentsline
\let\newlabel\oldnewlabel
\fi}
\fi}
\global\let\hyper@last\relax 
\gdef\HyperFirstAtBeginDocument#1{#1}
\providecommand\HyField@AuxAddToFields[1]{}
\providecommand\HyField@AuxAddToCoFields[2]{}
\@writefile{toc}{\contentsline {section}{\numberline {1}Background}{1}{section.1}}
\newlabel{sec:background}{{1}{1}{Background}{section.1}{}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.1}Setting Up the Router}{1}{subsection.1.1}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.2}Required Hardware}{1}{subsection.1.2}}
\newlabel{sec:required-hardware}{{1.2}{1}{Required Hardware}{subsection.1.2}{}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.3}Determine your Network Topology}{1}{subsection.1.3}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.4}Installing Red Hat Linux}{2}{subsection.1.4}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.5}Installing the Zebra routing software}{2}{subsection.1.5}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.6}Set up Configuration Files for Zebra}{3}{subsection.1.6}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.7}Turn on the Router Services}{3}{subsection.1.7}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.8}You Have Completed the Setup}{3}{subsection.1.8}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.9}The Virtual Terminal Interface, and Differences from Cisco IOS}{4}{subsection.1.9}}
\@writefile{toc}{\contentsline {section}{\numberline {2}An Example Session Setting Up the Computer in the Middle}{4}{section.2}}
\@writefile{lof}{\contentsline {figure}{\numberline {1}{\ignorespaces The arrangement with three computers.}}{4}{figure.1}}
\newlabel{fig:the-connections-between-three-routers.}{{1}{4}{The arrangement with three computers}{figure.1}{}}
\newlabel{1@xvr}{{}{4}{An Example Session Setting Up the Computer in the Middle}{figure.1}{}}
\newlabel{1@vr}{{}{4}{An Example Session Setting Up the Computer in the Middle}{figure.1}{}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.1}Setting up the Network Interfaces with the Zebra Service on Port 2601}{4}{subsection.2.1}}
\@writefile{toc}{\contentsline {section}{\numberline {3}Setting up RIP2 with the ripd Service on Port 2602}{5}{section.3}}
\@writefile{toc}{\contentsline {section}{\numberline {4}Viewing the routing Table using the route command:}{6}{section.4}}
\@writefile{toc}{\contentsline {section}{\numberline {5}Viewing the Network Devices using the ifconfig command:}{7}{section.5}}
\@writefile{toc}{\contentsline {section}{\numberline {6}Viewing the Addresses and Routing table using the ip command}{7}{section.6}}